‹

Cowl Moulding / Trim

Body and Frame › Cowl
Unified entry — merged from multiple cross-listed pages in the original manual.
Procedures
Cowl Panel Cover - Removal4 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Remove the wiper arms, Service and Repair.
  2. Remove the hood seal (3).
  3. Use a trim stick or equivalent, separate the cover assembly from the A-pillar.
  4. Remove the push pins (2) and remove the cowl grille (1) from the body (4).
Cowl Panel Cover - Installation4 steps
ℹ NOTE
The Vehicle Emission Control Information (VECI) label(s) must be in place for the life of the vehicle. When replacing the component in which the VECI label is adhered, a new VECI label must also be adhered to the new component.
Fig. 1
Fig. 1
  1. Position the cowl grille (1) and engage the clips to the bottom of the windshield.
  2. Install the push pins (2) through the cowl grille (1) and into the body (4).
  3. Install the hood seal (3).
  4. Install the wiper arms, Service and Repair
Cowl Panel Cover - Removal4 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Remove the wiper arms, Service and Repair.
  2. Remove the hood seal (3).
  3. Use a trim stick or equivalent, separate the cover assembly from the A-pillar.
  4. Remove the push pins (2) and remove the cowl grille (1) from the body (4).
Cowl Panel Cover - Installation4 steps
ℹ NOTE
The Vehicle Emission Control Information (VECI) label(s) must be in place for the life of the vehicle. When replacing the component in which the VECI label is adhered, a new VECI label must also be adhered to the new component.
Fig. 1
Fig. 1
  1. Position the cowl grille (1) and engage the clips to the bottom of the windshield.
  2. Install the push pins (2) through the cowl grille (1) and into the body (4).
  3. Install the hood seal (3).
  4. Install the wiper arms, Service and Repair
Cowl Panel Cover - Removal4 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Remove the wiper arms, Service and Repair.
  2. Remove the hood seal (3).
  3. Use a trim stick or equivalent, separate the cover assembly from the A-pillar.
  4. Remove the push pins (2) and remove the cowl grille (1) from the body (4).
Cowl Panel Cover - Installation4 steps
ℹ NOTE
The Vehicle Emission Control Information (VECI) label(s) must be in place for the life of the vehicle. When replacing the component in which the VECI label is adhered, a new VECI label must also be adhered to the new component.
Fig. 1
Fig. 1
  1. Position the cowl grille (1) and engage the clips to the bottom of the windshield.
  2. Install the push pins (2) through the cowl grille (1) and into the body (4).
  3. Install the hood seal (3).
  4. Install the wiper arms, Service and Repair
Factory service manual
From the 2008 KK factory manual — descriptions, specs, torque & procedures for this part.
SCREEN - TOP COWL📷 1
1.   Remove the wiper arms, refer to REMOVAL .
  2.   Remove the hood seal (3).
  3.   Use a trim stick C-4755 or equivalent, separate the cover assembly from the A-pillar.
  4.   Remove the push pins (2) and remove the cowl grille (1) from the body (4).
figure
SCREEN - TOP COWL📷 2
1. Position the cowl grille (1) and engage the clips to the bottom of the windshield. 2. Install the push pins (2) through the cowl grille (1) and into the body (4). 3. Install the hood seal (3).
4. Install the wiper arms, refer to INSTALLATION .
SHIELD - FRONT WHEELHOUSE SPLASH
figure
figure