‹

Memory Positioning Switch

Body and Frame › Mirrors
Unified entry — merged from multiple cross-listed pages in the original manual.
Procedures
Power Seat Memory Switch - Installation4 steps
Fig. 1
Fig. 1
  1. Install the memory seat switch (3) to the cluster bezel (2) and verify orientation.
  2. Install the two fasteners (2).
  3. Install the trim panels/bezels that were removed Instrument Cluster Bezel - Installation.
  4. Connect the negative battery cable.
Power Seat Memory Switch - Removal4 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Disconnect and isolate the battery negative cable.
  2. Remove trim panels/bezels as necessary to gain access to the memory seat switch Instrument Cluster Bezel - Removal.
  3. Remove the two fasteners (2).
  4. Remove the memory switch (3) from the cluster bezel (1).
Power Seat Memory Switch - Descriptionreference
Fig. 1
Fig. 1
DESCRIPTION Vehicles equipped with the memory system have a memory switch mounted to the lower left side of the instrument panel, below the air vent. This switch is used to set and recall all of the memory system settings for up to two drivers. The memory switch is a resistor multiplexed unit that is hard wired to the left Front Door Module (FDM). The left FDM in turn sends out the memory system set and recall requests to the other electronic modules over the Controller Area Network (CAN) data bus. The memory switch cannot be adjusted or repaired and must be replaced if inoperative or damaged.
Power Seat Memory Switch - Installation4 steps
Fig. 1
Fig. 1
  1. Install the memory seat switch (3) to the cluster bezel (2) and verify orientation.
  2. Install the two fasteners (2).
  3. Install the trim panels/bezels that were removed Instrument Cluster Bezel - Installation.
  4. Connect the negative battery cable.
Power Seat Memory Switch - Removal4 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Disconnect and isolate the battery negative cable.
  2. Remove trim panels/bezels as necessary to gain access to the memory seat switch Instrument Cluster Bezel - Removal.
  3. Remove the two fasteners (2).
  4. Remove the memory switch (3) from the cluster bezel (1).
Power Seat Memory Switch - Descriptionreference
Fig. 1
Fig. 1
DESCRIPTION Vehicles equipped with the memory system have a memory switch mounted to the lower left side of the instrument panel, below the air vent. This switch is used to set and recall all of the memory system settings for up to two drivers. The memory switch is a resistor multiplexed unit that is hard wired to the left Front Door Module (FDM). The left FDM in turn sends out the memory system set and recall requests to the other electronic modules over the Controller Area Network (CAN) data bus. The memory switch cannot be adjusted or repaired and must be replaced if inoperative or damaged.
Power Seat Memory Switch - Installation4 steps
Fig. 1
Fig. 1
  1. Install the memory seat switch (3) to the cluster bezel (2) and verify orientation.
  2. Install the two fasteners (2).
  3. Install the trim panels/bezels that were removed Instrument Cluster Bezel - Installation.
  4. Connect the negative battery cable.
Power Seat Memory Switch - Removal4 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Disconnect and isolate the battery negative cable.
  2. Remove trim panels/bezels as necessary to gain access to the memory seat switch Instrument Cluster Bezel - Removal.
  3. Remove the two fasteners (2).
  4. Remove the memory switch (3) from the cluster bezel (1).
Power Seat Memory Switch - Descriptionreference
Fig. 1
Fig. 1
DESCRIPTION Vehicles equipped with the memory system have a memory switch mounted to the lower left side of the instrument panel, below the air vent. This switch is used to set and recall all of the memory system settings for up to two drivers. The memory switch is a resistor multiplexed unit that is hard wired to the left Front Door Module (FDM). The left FDM in turn sends out the memory system set and recall requests to the other electronic modules over the Controller Area Network (CAN) data bus. The memory switch cannot be adjusted or repaired and must be replaced if inoperative or damaged.