‹

Engine Mount

Engine, Cooling and Exhaust › Engine
Unified entry — merged from multiple cross-listed pages in the original manual.

Parts

PartRight
ManufacturerCHY
OEM part #52129480AC
Price$133.00
PartLeft
ManufacturerCHY
OEM part #52129481AC
Price$138.00

Labor

Replace — Front Mount — Right1.4 hr
Warranty 0.0 hrSkill B
Left1.1 hr
Warranty 0.0 hrSkill B
Rear Mount0.6 hr
Warranty 0.0 hrSkill B
Procedures
Engine Mount Insulator - Installation — Rear12 steps
ℹ NOTE
4x2 shown, 4x4 similar.
ℹ NOTE
4x2 shown, 4x4 similar
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4
  1. Install the transmission mount (3) to the transmission. Install the bolts (2) and tighten.
  2. Position the crossmember in the vehicle. Install the crossmember to mount through bolt and nut.
  3. Install crossmember-to-sill bolts and tighten to 41 Nm (30 ft. lbs.)
  4. Remove the transmission support.
  5. Lower the vehicle.
  6. Connect negative cable to battery. AUTOMATIC TRANSMISSION:
  7. Install the transmission mount (2) to transmission and install the bolts (1).
  8. Position the crossmember in the vehicle. Install the crossmember to mount through bolt and nut.
  9. Install crossmember-to-sill bolts and tighten to 41 Nm (30 ft. lbs.)
  10. Remove the transmission support.
  11. Lower the vehicle.
  12. Connect negative cable to battery.
Engine Mount Insulator - Installation — Front6 steps
  1. Position the insulator mount and install the insulator mount through bolt.
  2. Lower the engine until the cylinder block-to-insulator mount bolts can be installed.
  3. Remove the jack and block of wood.
  4. Tighten the cylinder block-to-insulator mount bolts to 61 Nm ( 45 ft. lbs.).
  5. Install and tighten the through bolt retaining nut to 61 Nm (45 ft. lbs.).
  6. Install the fan blade, fan clutch and fan shroud.
Engine Mount Insulator - Removal — Rear3 steps
ℹ NOTE
A resilient rubber cushion supports the transmission at the rear between the transmission extension housing and the rear support crossmember or skid plate.
  1. Disconnect negative cable from battery.
  2. Raise the vehicle and support the transmission.
  3. Remove the nuts holding the support cushion to the crossmember. Remove the crossmember. MANUAL TRANSMISSION -Remove the support cushion nuts and remove the cushion. -Remove the transmission support bracket bolts and remove the bracket from the transmission. AUTOMATIC TRANSMISSION -Remove the support cushion bolts and remove the cushion and the support bracket from the transmission (4WD) or from the adaptor bracket (2WD). -On 2WD vehicles, remove the bolts holding the transmission support adaptor bracket to the transmission. Remove the adaptor bracket.
Engine Mount Insulator - Removal — Front6 steps
△ CAUTION
Remove the fan blade, fan clutch and fan shroud before raising engine. Failure to do so may cause damage to the fan blade, fan clutch and fan shroud.
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4
  1. Disconnect the negative cable from the battery.
  2. Remove the fan blade, fan clutch and fan shroud. Refer to COOLING SYSTEM for procedure.
  3. Remove the engine oil filter.
  4. Support the engine with a suitable jack and a block of wood across the full width of the engine oil pan.
  5. Remove the four cylinder block-to-insulator mount bolts (5) and the nut from the engine insulator mount through bolt.
  6. Using the jack, raise the engine high enough to remove the engine insulator mount thru bolt (2) and the insulator mount (Figure 1) and (Figure 2).
Factory service manual
From the 2008 KK factory manual — descriptions, specs, torque & procedures for this part.
REMOVAL FRONT ENGINE MOUNT📷 1
1 - MOUNT 2 - NUT
3 - SHIELD 4 - FASTENER 5 - BOLT 6 - THRU BOLT
1. Disconnect the negative cable from the battery.
CAUTION: Remove the fan blade, fan clutch and fan shroud before raising engine. Failure to do so may cause damage to the fan blade, fan clutch and fan shroud.
 2.   Remove the fan blade, fan clutch and fan shroud. Refer to COOLING for procedure.
 3.   Remove the engine oil filter.
 4.   Support the engine with a suitable jack and a block of wood across the full width of the engine oil pan.
 5.   Remove the four cylinder block-to-insulator mount bolts (5) and the nut from the engine insulator mount
through bolt.
1 - MOUNT 2 - THRU BOLT 3 - BOLT 4 - NUT
6. Using the jack, raise the engine high enough to remove the engine insulator mount thru bolt (2) and the insulator mount and. See Fig. 132. SeeFig. 133.
figure
INSTALLATION FRONT ENGINE MOUNT📷 1
1.   Position the insulator mount and install the insulator mount through bolt.
 2.   Lower the engine until the cylinder block-to-insulator mount bolts can be installed.
 3.   Remove the jack and block of wood.
 4.   Tighten the cylinder block-to-insulator mount bolts to 61 N.m (45 ft. lbs.).
 5.   Install and tighten the through bolt retaining nut to 61 N.m (45 ft. lbs.).
 6.   Install the fan blade, fan clutch and fan shroud.
MOUNT - ENGINE REAR
figure
ENGINE MOUNT - REAR
NOTE: A resilient rubber cushion supports the transmission at the rear between the transmission extension housing and the rear support crossmember or skid plate.
1. Disconnect negative cable from battery. 2. Raise the vehicle and support the transmission. 3. Remove the nuts holding the support cushion to the crossmember. Remove the crossmember.
MANUAL TRANSMISSION
Remove the support cushion nuts and remove the cushion. Remove the transmission support bracket bolts and remove the bracket from the transmission.
AUTOMATIC TRANSMISSION
Remove the support cushion bolts and remove the cushion and the support bracket from the transmission (4WD) or from the Adapter bracket (2WD). On 2WD vehicles, remove the bolts holding the transmission support Adapter bracket to the transmission. Remove the Adapter bracket.
MANUAL TRANSMISSION:📷 2
1 - TRANSMISSION MOUNT 2 - MOUNTING BOLT
1 - NUT 2 - BOLT 3 - TRANS MOUNT
1. Install the transmission mount (1) to the transmission. Install the bolts (2) and tighten. 2. Position the crossmember in the vehicle. Install the crossmember to mount through bolt and nut. 3. Install crossmember-to-sill bolts and tighten to 41 N.m (30 ft. lbs.)
4. Remove the transmission support. 5. Lower the vehicle. 6. Connect negative cable to battery.
figure
figure
AUTOMATIC TRANSMISSION:📷 2
1 - BOLT 2 - MOUNT
1 - MOUNT 2 - BOLT
  1.   Install the transmission mount to transmission. See Fig. 136 and Fig. 137. Install the bolts.
  2.   Position the crossmember in the vehicle. Install the crossmember to mount through bolt and nut.
  3.   Remove the transmission support.
  4.   Lower the vehicle.
  5.   Connect negative cable to battery.
LUBRICATION
figure
figure