‹

Dome Lamp Bulb

Lighting and Horns › Dome Lamp
Unified entry — merged from multiple cross-listed pages in the original manual.
Procedures
Dome Lamp Bulb - Installation — Second Row5 steps
△ CAUTION
Always use the correct bulb size and type for replacement. An incorrect bulb size or type may overheat and cause damage to the lamp, the socket or the lamp wiring.
ℹ NOTE
The second row reading lamps are integral to the grab handle in the headliner on the inner roof side rail over each outboard rear seating position. Refer to Body/Interior for the handle service procedure.
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Align the base of the bulb (1) with the bulb holder within the reading lamp housing.
  2. Push the bulb into the holder until the base is fully seated.
  3. Insert the large tab on the rear end of the lamp lens (1) into the rear of the lamp housing.
  4. Using hand pressure, push the small tab at the upper front corner of the lens (2) rearward and inward towards the lamp housing until it snaps into place.
  5. Reconnect the battery negative cable.
Dome Lamp Bulb - Installation — Front4 steps
△ CAUTION
Always use the correct bulb size and type for replacement. An incorrect bulb size or type may overheat and cause damage to the lamp, the socket or the lamp wiring.
Fig. 1
Fig. 1
  1. With the dome lamp lens (1) in the open position, align the ends of the bulb (3) with the two bulb holders within the front dome lamp housing (2).
  2. Carefully press the bulb firmly and evenly into the bulb holders until it snaps into place.
  3. Reinstall the lamp into the headliner. Dome Lamp - Installation.
  4. Reconnect the battery negative cable.
Dome Lamp Bulb - Removal — Second Row4 steps
ℹ NOTE
The second row reading lamps are integral to the grab handle in the headliner on the inner roof side rail over each outboard rear seating position. Refer to Body/Interior for the handle service procedure.
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Disconnect and isolate the battery negative cable.
  2. Using a small thin-bladed screwdriver, gently pry the upper corner at the forward end (2) of the reading lamp lens (1) away from the grab handle far enough to unsnap it from the lamp housing.
  3. Pull the front end of the lens outward far enough to disengage the large tab at the rear of the lens from the lamp housing.
  4. Pull the base of the bulb (1) straight out of the bulb holder within the lamp housing.
Dome Lamp Bulb - Removal — Front3 steps
Fig. 1
Fig. 1
  1. Disconnect and isolate the battery negative cable.
  2. Remove the front dome lamp from the headliner. Dome Lamp - Removal.
  3. With the lamp lens (1) in the open position, carefully unsnap the bulb (3) from the two bulb holders within the front dome lamp housing (2).
Factory service manual
From the 2008 KK factory manual — descriptions, specs, torque & procedures for this part.
FRONT DOME LAMP BULB📷 1
1. Disconnect and isolate the battery negative cable. 2. Remove the front dome lamp from the headliner. See REMOVAL. 3. With the lamp lens (1) in the open position, carefully unsnap the bulb (3) from the two bulb holders within the front dome lamp housing (2).
figure
SECOND ROW DOME/READING LAMP BULB📷 2
NOTE: The second row reading lamps are integral to the grab handle in the headliner
on the inner roof side rail over each outboard rear seating position. Refer to INTERIOR for the handle service procedure.
1. Disconnect and isolate the battery negative cable. 2. Using a small thin-bladed screwdriver, gently pry the upper corner at the forward end (2) of the reading lamp lens (1) away from the grab handle far enough to unsnap it from the lamp housing. 3. Pull the front end of the lens outward far enough to disengage the large tab at the rear of the lens from the lamp housing.
4. Pull the base of the bulb (1) straight out of the bulb holder within the lamp housing.
figure
figure
FRONT DOME LAMP BULB📷 1
CAUTION: Always use the correct bulb size and type for replacement. An incorrect bulb size or type may overheat and cause damage to the lamp, the socket or the lamp wiring.
1. With the dome lamp lens (1) in the open position, align the ends of the bulb (3) with the two bulb holders within the front dome lamp housing (2). 2. Carefully press the bulb firmly and evenly into the bulb holders until it snaps into place. 3. Reinstall the lamp into the headliner. See INSTALLATION. 4. Reconnect the battery negative cable.
figure
SECOND ROW DOME/READING LAMP BULB📷 2
CAUTION: Always use the correct bulb size and type for replacement. An incorrect bulb size or type may overheat and cause damage to the lamp, the socket or the lamp wiring.
NOTE: The second row reading lamps are integral to the grab handle in the headliner on the inner roof side rail over each outboard rear seating position. Refer to INTERIOR for the handle service procedure.
1. Align the base of the bulb (1) with the bulb holder within the reading lamp housing. 2. Push the bulb into the holder until the base is fully seated.
3. Insert the large tab on the rear end of the lamp lens (1) into the rear of the lamp housing. 4. Using hand pressure, push the small tab at the upper front corner of the lens (2) rearward and inward towards the lamp housing until it snaps into place. 5. Reconnect the battery negative cable.
GEAR SELECTOR LAMP
figure
figure