‹

Camshaft Position Sensor

Powertrain Management › Sensors and Switches - Powertrain Management
Unified entry — merged from multiple cross-listed pages in the original manual.

Parts

PartCamshaft Position Sensor
ManufacturerCHY
OEM part #5149054AC
Price$15.35
PartCamshaft Position Sensor
ManufacturerCHY
OEM part #5149054AC
Price$15.35
PartCamshaft Position Sensor
ManufacturerCHY
OEM part #5149054AC
Price$15.35
PartCamshaft Position Sensor
ManufacturerCHY
OEM part #5149054AC
Price$15.35

Labor

Replace0.4 hr
Warranty 0.0 hrSkill B
Replace0.4 hr
Warranty 0.0 hrSkill B
Replace0.4 hr
Warranty 0.0 hrSkill B
Replace0.4 hr
Warranty 0.0 hrSkill B
Procedures
Camshaft Position Sensor - Removal4 steps
ℹ NOTE
The Camshaft Position Sensor (CMP) is bolted to the front/top of the right cylinder head.
Fig. 1
Fig. 1
  1. Disconnect the electrical connector at CMP sensor (3).
  2. Remove the sensor mounting bolt (2).
  3. Carefully twist the sensor from the cylinder head (1).
  4. Check the condition of the sensor O-ring.
Camshaft Position Sensor - Installation5 steps
△ CAUTION
Before tightening sensor mounting bolt (2), be sure sensor is completely flush to cylinder head. If sensor is not flush, damage to sensor mounting tang may result.
Fig. 1
Fig. 1
  1. Clean out machined hole in cylinder head.
  2. Apply a small amount of engine oil to sensor o-ring.
  3. Install sensor (3) into cylinder head with a slight rocking and twisting action.
  4. Install mounting bolt (2) and tighten to 12 Nm (106 in.lbs).
  5. Connect electrical connector to sensor.
Camshaft Position Sensor - Removal4 steps
ℹ NOTE
The Camshaft Position Sensor (CMP) is bolted to the front/top of the right cylinder head.
Fig. 1
Fig. 1
  1. Disconnect the electrical connector at CMP sensor (3).
  2. Remove the sensor mounting bolt (2).
  3. Carefully twist the sensor from the cylinder head (1).
  4. Check the condition of the sensor O-ring.
Camshaft Position Sensor - Installation5 steps
△ CAUTION
Before tightening sensor mounting bolt (2), be sure sensor is completely flush to cylinder head. If sensor is not flush, damage to sensor mounting tang may result.
Fig. 1
Fig. 1
  1. Clean out machined hole in cylinder head.
  2. Apply a small amount of engine oil to sensor o-ring.
  3. Install sensor (3) into cylinder head with a slight rocking and twisting action.
  4. Install mounting bolt (2) and tighten to 12 Nm (106 in.lbs).
  5. Connect electrical connector to sensor.
Camshaft Position Sensor - Removal4 steps
ℹ NOTE
The Camshaft Position Sensor (CMP) is bolted to the front/top of the right cylinder head.
Fig. 1
Fig. 1
  1. Disconnect the electrical connector at CMP sensor (3).
  2. Remove the sensor mounting bolt (2).
  3. Carefully twist the sensor from the cylinder head (1).
  4. Check the condition of the sensor O-ring.
Camshaft Position Sensor - Installation5 steps
△ CAUTION
Before tightening sensor mounting bolt (2), be sure sensor is completely flush to cylinder head. If sensor is not flush, damage to sensor mounting tang may result.
Fig. 1
Fig. 1
  1. Clean out machined hole in cylinder head.
  2. Apply a small amount of engine oil to sensor o-ring.
  3. Install sensor (3) into cylinder head with a slight rocking and twisting action.
  4. Install mounting bolt (2) and tighten to 12 Nm (106 in.lbs).
  5. Connect electrical connector to sensor.
Camshaft Position Sensor - Removal4 steps
ℹ NOTE
The Camshaft Position Sensor (CMP) is bolted to the front/top of the right cylinder head.
Fig. 1
Fig. 1
  1. Disconnect the electrical connector at CMP sensor (3).
  2. Remove the sensor mounting bolt (2).
  3. Carefully twist the sensor from the cylinder head (1).
  4. Check the condition of the sensor O-ring.
Camshaft Position Sensor - Installation5 steps
△ CAUTION
Before tightening sensor mounting bolt (2), be sure sensor is completely flush to cylinder head. If sensor is not flush, damage to sensor mounting tang may result.
Fig. 1
Fig. 1
  1. Clean out machined hole in cylinder head.
  2. Apply a small amount of engine oil to sensor o-ring.
  3. Install sensor (3) into cylinder head with a slight rocking and twisting action.
  4. Install mounting bolt (2) and tighten to 12 Nm (106 in.lbs).
  5. Connect electrical connector to sensor.
Camshaft Position Sensor - Removal4 steps
ℹ NOTE
The Camshaft Position Sensor (CMP) is bolted to the front/top of the right cylinder head.
Fig. 1
Fig. 1
  1. Disconnect the electrical connector at CMP sensor (3).
  2. Remove the sensor mounting bolt (2).
  3. Carefully twist the sensor from the cylinder head (1).
  4. Check the condition of the sensor O-ring.
Camshaft Position Sensor - Installation5 steps
△ CAUTION
Before tightening sensor mounting bolt (2), be sure sensor is completely flush to cylinder head. If sensor is not flush, damage to sensor mounting tang may result.
Fig. 1
Fig. 1
  1. Clean out machined hole in cylinder head.
  2. Apply a small amount of engine oil to sensor o-ring.
  3. Install sensor (3) into cylinder head with a slight rocking and twisting action.
  4. Install mounting bolt (2) and tighten to 12 Nm (106 in.lbs).
  5. Connect electrical connector to sensor.
Camshaft Position Sensor - Removal4 steps
ℹ NOTE
The Camshaft Position Sensor (CMP) is bolted to the front/top of the right cylinder head.
Fig. 1
Fig. 1
  1. Disconnect the electrical connector at CMP sensor (3).
  2. Remove the sensor mounting bolt (2).
  3. Carefully twist the sensor from the cylinder head (1).
  4. Check the condition of the sensor O-ring.
Camshaft Position Sensor - Installation5 steps
△ CAUTION
Before tightening sensor mounting bolt (2), be sure sensor is completely flush to cylinder head. If sensor is not flush, damage to sensor mounting tang may result.
Fig. 1
Fig. 1
  1. Clean out machined hole in cylinder head.
  2. Apply a small amount of engine oil to sensor o-ring.
  3. Install sensor (3) into cylinder head with a slight rocking and twisting action.
  4. Install mounting bolt (2) and tighten to 12 Nm (106 in.lbs).
  5. Connect electrical connector to sensor.