‹

Ignition Switch Lock Cylinder

Starting and Charging › Starting System
Unified entry — merged from multiple cross-listed pages in the original manual.

Parts

PartIgnition Lock Cylinder
ManufacturerCHY
OEM part #5179511AA
Price$51.35
PartIgnition Lock Cylinder
ManufacturerCHY
OEM part #5179511AA
Price$51.35

Labor

Replace0.5 hr
Warranty 0.0 hrSkill B
Replace0.5 hr
Warranty 0.0 hrSkill B
Procedures
Ignition Lock Cylinder - Removal4 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4
  1. Disconnect negative cable from battery.
  2. Remove upper and lower covers (shrouds) from steering column.
  3. Place shifter in PARK position.
  4. A retaining pin (Figure 1) is located at side of key cylinder assembly (2). a.Rotate key to RUN position. b.Press in on retaining pin while pulling key cylinder (1) from ignition switch.
Ignition Lock Cylinder - Installation6 steps
Fig. 1
Fig. 1
  1. Install the key cylinder (2) into the housing (3) using care to align the end of the key cylinder with the ignition switch.
  2. Push the key cylinder (2) in until it clicks.
  3. Rotate the key to the insert position.
  4. Install the halo ring around the key cylinder housing.
  5. Install the (S.K.R.E.E.M) module.
  6. Install the shroud covers.
Ignition Lock Cylinder - Removal4 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4
  1. Disconnect negative cable from battery.
  2. Remove upper and lower covers (shrouds) from steering column.
  3. Place shifter in PARK position.
  4. A retaining pin (Figure 1) is located at side of key cylinder assembly (2). a.Rotate key to RUN position. b.Press in on retaining pin while pulling key cylinder (1) from ignition switch.
Ignition Lock Cylinder - Installation6 steps
Fig. 1
Fig. 1
  1. Install the key cylinder (2) into the housing (3) using care to align the end of the key cylinder with the ignition switch.
  2. Push the key cylinder (2) in until it clicks.
  3. Rotate the key to the insert position.
  4. Install the halo ring around the key cylinder housing.
  5. Install the (S.K.R.E.E.M) module.
  6. Install the shroud covers.
Factory service manual
From the 2008 KK factory manual — descriptions, specs, torque & procedures for this part.
LOCK CYLINDER HOUSING📷 1
1 - KEY 2 - KEY CYLINDER 3 - RETAINING PIN HOLE
The ignition key (1) must be in the key cylinder (2) for cylinder removal.
  1.   Disconnect negative cable from battery.
  2.   Remove upper and lower covers (shrouds) from steering column.
  3.   Place shifter in PARK position.
  4.   A retaining pin is located at side of key cylinder assembly (2). See Fig. 20.
1 - KEY CYLINDER 2 - PUNCH
 Rotate key to RUN position.  Press in on retaining pin while pulling key cylinder (1) from ignition switch. See Fig. 21.
figure
LOCK CYLINDER HOUSING📷 1
1 - KEY 2 - KEY CYLINDER 3 - RETAINING PIN HOLE
The ignition key (1) must be in the key cylinder (2) for cylinder installation.
1. Install the key cylinder into the housing using care to align the end of the key cylinder (2) with the ignition switch. 2. Push the key cylinder (2) in until it clicks. 3. Replace the upper and lower shrouds. 4. Reconnect the battery.
PLUG-GLOW 2.8L DIESEL
figure