‹

Wheel Stud / Lug Nut

Steering and Suspension › Wheels and Tires
Unified entry — merged from multiple cross-listed pages in the original manual.

Labor

Replace — Front Suspension — Lug Bolts — One Side — One1.3 hr
Warranty 0.0 hrSkill B
To R&R Each Additional Stud, Add0.2 hr
Warranty 0.0 hrSkill B
Rear Suspension — Lug Bolts — One Side — One1.3 hr
Warranty 0.0 hrSkill B
To R&R Each Additional Stud, Add0.2 hr
Warranty 0.0 hrSkill B
Procedures
Wheel Stud / Lug Nut: Specificationsreference
Fig. 1
Fig. 1
WHEEL STUD / LUG NUT Wheel Lug Nut 136 ± 20 Nm (100 ± 15 ft.lbs.)
Wheel Stud - Installation — Rear7 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Install the new stud (1) into the hub flange by rotating the stud (1) in between the hub/bearing and park brake shoes (2).
  2. Install the three washers onto the stud, then install the lug nut with the flat side of the nut against the washers.
  3. Tighten the lug nut until the stud is pulled into the hub flange. Verify that the stud is properly seated into the flange.
  4. Remove the lug nut and washers.
  5. Install the brake rotor and caliper,Disc Brake Caliper - Installation.
  6. Install the wheel and tire assembly, use new lug nut on stud or studs that were replaced.
  7. Remove the support and lower vehicle.
Wheel Stud - Installation — Front7 steps
△ CAUTION
Do not use a hammer to remove wheel studs.
  1. Install the new stud into the hub flange.
  2. Install the three washers onto the stud, then install the lug nut with the flat side of the nut against the washers.
  3. Tighten the lug nut until the stud is pulled into the hub flange. Verify that the stud is properly seated into the flange.
  4. Remove the lug nut and washers.
  5. Install the brake rotor, caliper adapter, and caliper,Disc Brake Caliper - Installation.
  6. Install the wheel and tire assembly, use new lug nut on stud or studs that were replaced.
  7. Remove the support and lower vehicle.
Wheel Stud - Removal — Rear5 steps
△ CAUTION
Do not use a hammer to remove wheel studs.
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4
Fig. 5
Fig. 5
  1. Raise and support vehicle.
  2. Remove wheel and tire assembly.
  3. Remove brake caliper and rotor,Brake Rotor - Removal.
  4. Remove stud (2) from hub with Remover (1).
  5. Remove the stud (1) from between the hub/bearing and brake shoes (2)
Wheel Stud - Removal — Front4 steps
△ CAUTION
Do not use a hammer to remove wheel studs.
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
  1. Raise and support vehicle.
  2. Remove wheel and tire assembly.
  3. Remove brake caliper, caliper adapter and rotor,Brake Rotor - Removal.
  4. Remove stud (2) from hub with Remover A (1).
Factory service manual
From the 2008 KK factory manual — descriptions, specs, torque & procedures for this part.
FRONT WHEEL STUD📷 1
1 - C-4150-A 2 - STUD
CAUTION: Do not use a hammer to remove wheel studs.
 1.   Raise and support vehicle.
 2.   Remove wheel and tire assembly.
 3.   Remove brake caliper, caliper adapter and rotor. Refer to REMOVAL .
 4.   Remove stud (2) from hub with Remover C-4150-A (1).
figure
REAR WHEEL STUD📷 3
CAUTION: Do not use a hammer to remove wheel studs.
1. Raise and support vehicle. 2. Remove wheel and tire assembly.
1 - SPECIAL TOOL 8677 2 - STUD
3. Remove brake caliper and rotor. Refer to REMOVAL . 4. Remove stud (2) from hub with Remover 8677 (1).
1 - STUD 2 - PARK BRAKE SHOE
5. Remove the stud (1) from between the hub/bearing and brake shoes (2)
figure
figure
figure
FRONT WHEEL STUD📷 1
CAUTION: Do not use a hammer to remove wheel studs.
1. Install the new stud into the hub flange. 2. Install the three washers onto the stud, then install the lug nut with the flat side of the nut against the washers. 3. Tighten the lug nut until the stud is pulled into the hub flange. Verify that the stud is properly seated into the flange. 4. Remove the lug nut and washers. 5. Install the brake rotor, caliper adapter, and caliper. Refer to INSTALLATION . 6. Install the wheel and tire assembly, use new lug nut on stud or studs that were replaced. 7. Remove the support and lower vehicle.
figure
REAR WHEEL STUD📷 1
1 - STUD 2 - PARK BRAKE SHOE
1. Install the new stud (1) into the hub flange by rotating the stud (1) in between the hub/bearing and park brake shoes (2). 2. Install the three washers onto the stud, then install the lug nut with the flat side of the nut against the washers. 3. Tighten the lug nut until the stud is pulled into the hub flange. Verify that the stud is properly seated into the flange. 4. Remove the lug nut and washers.
5. Install the brake rotor and caliper. Refer to INSTALLATION . 6. Install the wheel and tire assembly, use new lug nut on stud or studs that were replaced. 7. Remove the support and lower vehicle.
TIRE PRESSURE MONITORING SYSTEM
figure