‹

Transmission Control System Relay

Transmission and Drivetrain › Relays and Modules - Transmission and Drivetrain
Unified entry — merged from multiple cross-listed pages in the original manual.
Procedures
Transmission Control Relay - Operationreference
ℹ NOTE
Due to different power control configurations, the Transmission Control Relay (if equipped) may be referred to as a PCM relay.
OPERATION When the relay is "off", no power is supplied to the solenoid pack and the transmission is in "limp-in" mode. After a controller reset, the TCM energizes the relay. Prior to this, the TCM verifies that the contacts are open by checking for no voltage at the switched battery terminals. After this is verified, the voltage at the solenoid pack pressure switches is checked. After the relay is energized, the TCM monitors the terminals to verify that the voltage is greater than 3 volts.
Transmission Control Relay - Descriptionreference
ℹ NOTE
Due to different power control configurations, the Transmission Control Relay (if equipped) may be referred to as a PCM relay.
DESCRIPTION The relay is supplied fused B+ voltage, energized by the TCM, and is used to supply power to the solenoid pack when the transmission is in normal operating mode.
Transmission Control Relay - Operationreference
ℹ NOTE
Due to different power control configurations, the Transmission Control Relay (if equipped) may be referred to as a PCM relay.
OPERATION When the relay is "off", no power is supplied to the solenoid pack and the transmission is in "limp-in" mode. After a controller reset, the TCM energizes the relay. Prior to this, the TCM verifies that the contacts are open by checking for no voltage at the switched battery terminals. After this is verified, the voltage at the solenoid pack pressure switches is checked. After the relay is energized, the TCM monitors the terminals to verify that the voltage is greater than 3 volts.
Transmission Control Relay - Descriptionreference
ℹ NOTE
Due to different power control configurations, the Transmission Control Relay (if equipped) may be referred to as a PCM relay.
DESCRIPTION The relay is supplied fused B+ voltage, energized by the TCM, and is used to supply power to the solenoid pack when the transmission is in normal operating mode.
Transmission Control Relay - Operationreference
ℹ NOTE
Due to different power control configurations, the Transmission Control Relay (if equipped) may be referred to as a PCM relay.
OPERATION When the relay is "off", no power is supplied to the solenoid pack and the transmission is in "limp-in" mode. After a controller reset, the TCM energizes the relay. Prior to this, the TCM verifies that the contacts are open by checking for no voltage at the switched battery terminals. After this is verified, the voltage at the solenoid pack pressure switches is checked. After the relay is energized, the TCM monitors the terminals to verify that the voltage is greater than 3 volts.
Transmission Control Relay - Descriptionreference
ℹ NOTE
Due to different power control configurations, the Transmission Control Relay (if equipped) may be referred to as a PCM relay.
DESCRIPTION The relay is supplied fused B+ voltage, energized by the TCM, and is used to supply power to the solenoid pack when the transmission is in normal operating mode.
Transmission Control Relay - Operationreference
ℹ NOTE
Due to different power control configurations, the Transmission Control Relay (if equipped) may be referred to as a PCM relay.
OPERATION When the relay is "off", no power is supplied to the solenoid pack and the transmission is in "limp-in" mode. After a controller reset, the TCM energizes the relay. Prior to this, the TCM verifies that the contacts are open by checking for no voltage at the switched battery terminals. After this is verified, the voltage at the solenoid pack pressure switches is checked. After the relay is energized, the TCM monitors the terminals to verify that the voltage is greater than 3 volts.
Transmission Control Relay - Descriptionreference
ℹ NOTE
Due to different power control configurations, the Transmission Control Relay (if equipped) may be referred to as a PCM relay.
DESCRIPTION The relay is supplied fused B+ voltage, energized by the TCM, and is used to supply power to the solenoid pack when the transmission is in normal operating mode.