‹

Rear Door Window Glass

Body and Frame › Doors, Hood and Trunk
Unified entry — merged from multiple cross-listed pages in the original manual.
Procedures
Rear Door Glass - Installation11 steps
ℹ NOTE
The following two graphics are shown with the carrier removed for clarity.
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4
Fig. 5
Fig. 5
Fig. 6
Fig. 6
  1. Install the door glass to the window opening in the door.
  2. Verify that the glass is seated into both glass run channels.
  3. Push the glass (1) down and seat the clips (2) fully.
  4. Pull up on the glass and make sure that it is secure.
  5. Position the quarter glass (2) back into the window opening.
  6. Twist the top of the fixed glass (2) back into place and seat the glass into the door frame fully.
  7. Seat the glass run seal (1) around the door frame fully.
  8. Install the devision bar bolt (1).
  9. Press the belt molding onto the trim panel flange starting at the rear and working forward.
  10. Install the trim panel Rear Door Trim Panel - Installation.
  11. Cycle the window several times to make sure the window doesn't bind on the outer weatherstrip or run channel.
Rear Door Glass - Removal9 steps
△ CAUTION
Do not attempt to remove the trim panel the conventional way. This door panel has hooks holding it to the door rather than push pins. Carefully follow these instructions in order to prevent unnecessary damage to the trim panel.
ℹ NOTE
Place the glass in the full down position in order to release the glass from the window regulator lift plate. If the glass is released from the lift plate in any other position other than full down, the carrier plate will need to be removed in order to re-position the regulator cable onto the guides and place the lift plate into the full down position for correct installation of the glass.
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4
Fig. 5
Fig. 5
Fig. 6
Fig. 6
  1. Remove the trim panel Rear Door Trim Panel - Removal.
  2. Rotate the inner belt molding outboard while pulling up to disengage the retention tabs.
  3. Remove the bolt securing the fixed door glass to the door.
  4. Separate the glass seal from the top of the door frame (1).
  5. Twist the top of the fixed glass (2) towards the glass opening, remove the glass and position aside.
  6. If required, reinstall the regulator handle or window switch to enable lowering of the glass (1) for access to the glass attachment clips (2)
  7. Position the glass into the full down position.
  8. Access the window regulator through the hole in the carrier plate. Disconnect the window regulator (2) from the door glass (1).
  9. Remove the door glass from the window opening in the door.
Factory service manual
From the 2008 KK factory manual — descriptions, specs, torque & procedures for this part.
GLASS - REAR DOOR📷 4
1. Remove the trim panel. See REMOVAL.
2. Rotate the inner belt molding outboard while pulling up to disengage the retention tabs.
NOTE: Place the glass in the full down position in order to access the window regulator.
3. Access the window regulator through the hole in the carrier plate. Disconnect the window regulator (2) from the door glass (1).
NOTE: The following two graphics are shown with the carrier removed for clarity.
4. Rotate the glass upward inside the run channel.
5. Remove the door glass from the window opening in the door.
figure
figure
figure
figure
GLASS - REAR DOOR📷 4
NOTE: The following two graphics are shown with the carrier removed for clarity.
1. Install the door glass to the window opening in the door.
2. Rotate the glass downward into the run channel.
3. Access the window regulator through the hole in the carrier plate. Connect the door glass (1) to the window regulator (2).
4. Press the belt molding onto the trim panel flange starting at the rear and working forward.
5. Install the trim panel. See INSTALLATION. 6. Cycle the window several times to make sure the window doesn't bind on the outer weatherstrip or run channel.
HANDLE - EXTERIOR DOOR
figure
figure
figure
figure