‹

Console

Body and Frame › Interior Moulding / Trim
Unified entry — merged from multiple cross-listed pages in the original manual.
Procedures
Floor Console Base - Removal12 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4
  1. Disconnect and isolate battery negative cable.
  2. Using a trim stick or equivalent, pry the shift bezel out of the floor console.
  3. If equipped, remove electrical connectors attached to shift bezel.
  4. Open console lid (1).
  5. Using a trim stick or equivalent, release the fasteners at the four locations around the floor console end cap (2).
  6. Disconnect electrical connectors (3) from end cap (2).
  7. Remove end cap (2).
  8. Remove ash cup (3) from console (1).
  9. Remove bin (4) from console (1).
  10. Remove two screws (2) from front of console (1).
  11. Remove two screws (5) from rear of console (1) located inside the console bin.
  12. Lift console (1) at back and remove.
Floor Console End Cap - Removal4 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Open console lid (1).
  2. Using a trim stick or equivalent, release the fasteners at the four locations around the floor console end cap (2).
  3. Disconnect electrical connectors (3) from end cap (2).
  4. Remove end cap (2).
Floor Console Lid Latch - Installation2 steps
ℹ NOTE
Align the lid latch (2) with the reference marks made during removal.
Fig. 1
Fig. 1
  1. Install the two screws (1) attaching the console lid latch (2) to the console lid (3).
  2. Check the adjustment of the lid latch (2) and adjust as necessary by loosening the two screws (1) and moving the lid latch (2) right or left as needed until the console lid (3) closes properly.
Front Overhead Console - Installation4 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Position the overhead console (1) in the vehicle near the headliner assembly.
  2. If equipped, connect the courtesy lamps, infrared temperature sensor and power sunroof switch electrical connectors (2).
  3. Grasp the sides of the overhead console (2) and push straight up evenly to engage the three snap clips (1) into the mounting bracket.
  4. Connect the battery negative cable.
Floor Console End Cap - Installation2 steps
Fig. 1
Fig. 1
  1. Connect the electrical connectors (3) to the end cap (2).
  2. Align the end cap (2) to the console, use hand pressure to seat the clips.
Floor Console Lid Latch - Removal2 steps
ℹ NOTE
Using a grease pencil or equivalent, mark location of lid latch (2) on the console lid (3) for installation alignment.
Fig. 1
Fig. 1
  1. Remove the two screws (1) attaching the console lid latch (2) to the console lid (3).
  2. Remove the lid latch (2) from the console lid (3).
Floor Console Lid - Installation4 steps
Fig. 1
Fig. 1
  1. Install the hinge (3) to the console (4).
  2. Install the three screws (5) attaching hinge (3) to the console (4).
  3. Install the console lid (2) to the hinge (3).
  4. Install the two screws (1) attaching the console lid (2) to the hinge (3).
Floor Console Lid - Removal4 steps
Fig. 1
Fig. 1
  1. Remove the two screws (1) attaching the console lid (2) to the hinge (3).
  2. Remove the console lid (2) from the hinge (3).
  3. Remove the three screws (5) attaching the hinge (3) to the console (4).
  4. Remove the hinge (3) from the console (4).
Floor Console Base - Installation10 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
  1. Install the console (1) into the vehicle.
  2. Install the two screws (5) to the rear of the console (1), located inside the console bin.
  3. Install the two screws (2) in the front of console (1).
  4. Install the bin (4) to the console (1).
  5. Install the ash cup (3) to the console (1).
  6. Connect the electrical connectors (3) to the end cap (2).
  7. Align the end cap (2) to the console, use hand pressure to seat the clips.
  8. If equipped, connect electrical connectors attached to shift bezel.
  9. Align and use hand pressure to install the shift bezel into the floor console.
  10. Connect battery negative cable.
Front Overhead Console - Removal5 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Disconnect and isolate the battery negative cable.
  2. Using your fingertips, grasp the sides of the overhead console (1) and pull straight down evenly to disengage the three snap clips from the mounting bracket.
  3. Lower the overhead console (1) far enough to access the wire harness connector (2).
  4. If equipped, disconnect the courtesy lamps, infrared temperature sensor and power sunroof switch electrical connectors.
  5. Remove the overhead console (1) assembly from the vehicle.
Console: Description and Operationreference
Fig. 1
Fig. 1
DESCRIPTION An overhead console (1) is standard factory-installed equipment on this model. All overhead consoles are equipped with two reading and courtesy lamps (3). On vehicles equipped with a power sunroof, the sunroof switch (2) is located between the two reading and courtesy lamps. On vehicles equipped with automatic climate control an infrared temperature sensor (4) is located on the front edge of the overhead console. The overhead console is mounted with three snap clips into a molded plastic retainer bracket located above the headliner to provide secure overhead console attachment.
Factory service manual
From the 2008 KK factory manual — descriptions, specs, torque & procedures for this part.
BASE - FLOOR CONSOLE📷 2
1. Using a trim stick C-4755 or equivalent, pry the shift bezel out of the floor console. 2. If equipped, remove electrical connectors attached to shift bezel.
3. Open console lid (1). 4. Using a trim stick C-4755 or equivalent, release the fasteners at the four locations around the floor console end cap (2). 5. Disconnect electrical connectors (3) from end cap (2). 6. Remove end cap (2).
  7.   Remove ash cup (3) from console (1).
  8.   Remove bin (4) from console (1).
  9.   Remove two screws (2) from front of console (1).
 10.   Remove two screws (5) from rear of console (1) located inside the console bin.
 11.   Lift console (1) at back and remove.
figure
figure
BASE - FLOOR CONSOLE📷 4
1. Install the console (1) into the vehicle. 2. Install the two screws (5) to the rear of the console (1), located inside the console bin.
3. Install the two screws (2) in the front of console (1). 4. Install the bin (4) to the console (1). 5. Install the ash cup (3) to the console (1).
6. Connect the electrical connectors (3) to the end cap (2). 7. Align the end cap (2) to the console, use hand pressure to seat the clips.
8. If equipped, connect electrical connectors attached to shift bezel. 9. Align and use hand pressure to install the shift bezel into the floor console.
BEZEL - CONSOLE SHIFT
figure
figure
figure
figure
BEZEL - CONSOLE SHIFT📷 1
1. If equipped with a manual transmission and built before February 11, 2008, using a slide-hammer, snap out the shift knob from the lever.
2. Using a trim stick C-4755 or equivalent, pry the shift bezel out of the floor console. If equipped with a manual transmission, the lever boot will come off with the bezel. 3. If equipped, remove electrical connectors attached to shift bezel. 4. If equipped with a manual transmission and built on or after February 11, 2008, using a slide-hammer, snap out the shift knob from the lever.
NOTE: If equipped with a manual transmission and built on or after February 11, 2008, to remove the boot from the console bezel, operate the retaining clips to release the boot frame. Do not attempt using a trim stick on the top surface, that will damage the part.
figure
BEZEL - CONSOLE SHIFT📷 1
1. If equipped with a manual transmission and built on or after February 11, 2008, snap in the shift knob on the shift lever.
2. If equipped, connect electrical connectors attached to shift bezel. 3. Align and use hand pressure to install the shift bezel into the floor console. 4. If equipped with a manual transmission and built before February 11, 2008, snap in the shift knob on the shift lever.
CARPET - FLOOR
figure
CAP - FLOOR CONSOLE END📷 1
1. Open console lid (1). 2. Using a trim stick C-4755 or equivalent, release the fasteners at the four locations around the floor console end cap (2). 3. Disconnect electrical connectors (3) from end cap (2). 4. Remove end cap (2).
figure
CAP - FLOOR CONSOLE END📷 2
1. Connect the electrical connectors (3) to the end cap (2). 2. Align the end cap (2) to the console, use hand pressure to seat the clips.
FLOOR - LOAD
figure
figure
LATCH - ARMREST LID📷 1
NOTE: Using a grease pencil or equivalent, mark location of lid latch (2) on the console lid (3) for installation alignment.
1. Remove the two screws (1) attaching the console lid latch (2) to the console lid (3). 2. Remove the lid latch (2) from the console lid (3).
figure
LATCH - ARMREST LID📷 2
NOTE: Align the lid latch (2) with the reference marks made during removal.
1. Install the two screws (1) attaching the console lid latch (2) to the console lid (3). 2. Check the adjustment of the lid latch (2) and adjust as necessary by loosening the two screws (1) and moving the lid latch (2) right or left as needed until the console lid (3) closes properly.
LID - FLOOR CONSOLE
figure
figure
LID - FLOOR CONSOLE📷 1
1.   Remove the two screws (1) attaching the console lid (2) to the hinge (3).
  2.   Remove the console lid (2) from the hinge (3).
  3.   Remove the three screws (5) attaching the hinge (3) to the console (4).
  4.   Remove the hinge (3) from the console (4).
figure
LID - FLOOR CONSOLE📷 1
1.   Install the hinge (3) to the console (4).
  2.   Install the three screws (5) attaching hinge (3) to the console (4).
  3.   Install the console lid (2) to the hinge (3).
  4.   Install the two screws (1) attaching the console lid (2) to the hinge (3).
MIRROR - REAR VIEW
figure