‹

Rear Door Weatherstrip

Body and Frame › Weatherstrip
Unified entry — merged from multiple cross-listed pages in the original manual.
Procedures
Rear Door Inner Belt Weatherstrip - Removal2 steps
Fig. 1
Fig. 1
  1. Remove the door trim panel, Rear Door Trim Panel - Removal.
  2. Rotate the inner belt molding outboard while pulling up to disengage the retention tabs.
Rear Door Opening Seal - Installation2 steps
ℹ NOTE
Position the seal to the bottom of the door opening, with bulb facing outboard, starting the installation at the center of the lower flange. Press the seal onto the sill flange and work around the perimeter of the door opening until fully seated. Work 1/2 the way around and then start at the other end of the seal working back, making sure the splice joint has no gap and smoothing the seal to avoid puckers or wrinkles. If in extreme cold temperatures preheating the weatherstrip to 23.8° C (75° F) may be required to fully seat the weatherstrip.
Fig. 1
Fig. 1
  1. Install the weatherstrip to the body mount flange.
  2. Trim the weatherstrip if necessary, and connect the ends together along the flange.
Rear Door Weatherstrip - Removal1 step
Fig. 1
Fig. 1
  1. Carefully remove the plastic hook style clips on the weatherstrip from the door and remove the seal from the door.
Rear Door Weatherstrip - Installation1 step
Fig. 1
Fig. 1
  1. Position the seal correctly and install the plastic hook style clips on the weatherstrip to the door.
Rear Door Opening Seal - Removal2 steps
Fig. 1
Fig. 1
  1. Open the rear door.
  2. Remove weatherstrip from the body mount flange.
Rear Door Inner Belt Weatherstrip - Installation2 steps
Fig. 1
Fig. 1
  1. Press the belt molding onto the trim panel flange starting at the rear and working forward.
  2. Install the door trim panel, Rear Door Trim Panel - Installation.
Rear Door Inner Belt Weatherstrip - Removal2 steps
Fig. 1
Fig. 1
  1. Remove the door trim panel, Rear Door Trim Panel - Removal.
  2. Rotate the inner belt molding outboard while pulling up to disengage the retention tabs.
Rear Door Opening Seal - Installation2 steps
ℹ NOTE
Position the seal to the bottom of the door opening, with bulb facing outboard, starting the installation at the center of the lower flange. Press the seal onto the sill flange and work around the perimeter of the door opening until fully seated. Work 1/2 the way around and then start at the other end of the seal working back, making sure the splice joint has no gap and smoothing the seal to avoid puckers or wrinkles. If in extreme cold temperatures preheating the weatherstrip to 23.8° C (75° F) may be required to fully seat the weatherstrip.
Fig. 1
Fig. 1
  1. Install the weatherstrip to the body mount flange.
  2. Trim the weatherstrip if necessary, and connect the ends together along the flange.
Rear Door Weatherstrip - Removal1 step
Fig. 1
Fig. 1
  1. Carefully remove the plastic hook style clips on the weatherstrip from the door and remove the seal from the door.
Rear Door Weatherstrip - Installation1 step
Fig. 1
Fig. 1
  1. Position the seal correctly and install the plastic hook style clips on the weatherstrip to the door.
Rear Door Opening Seal - Removal2 steps
Fig. 1
Fig. 1
  1. Open the rear door.
  2. Remove weatherstrip from the body mount flange.
Rear Door Inner Belt Weatherstrip - Installation2 steps
Fig. 1
Fig. 1
  1. Press the belt molding onto the trim panel flange starting at the rear and working forward.
  2. Install the door trim panel, Rear Door Trim Panel - Installation.
Factory service manual
From the 2008 KK factory manual — descriptions, specs, torque & procedures for this part.
WEATHERSTRIP - RDB - INNER📷 1
1. Remove the door trim panel, see REMOVAL. 2. Rotate the inner belt molding outboard while pulling up to disengage the retention tabs.
figure
WEATHERSTRIP - RDB - INNER📷 1
1. Press the belt molding onto the trim panel flange starting at the rear and working forward. 2. Install the door trim panel, see INSTALLATION.
WEATHERSTRIP - RDB - OUTER
figure
WEATHERSTRIP - RDB - OUTER📷 2
1 - OUTER BELT MOLDING 2 - SPECIAL TOOL #9093 3 - RETAINING TAB 4 - DOOR OUTER PANEL
1. Lower window completely. 2. Insert the outer door belt molding removal tool - 9093 between belt molding and glass at rear and then slide tool forward approximately 14 cm (5.5 in.). 3. Push down on outer belt molding and rotate upper part of tool outward from vehicle approximately 6 - 8
cm (2.5 - 3 in.) then lift up on molding to disengage from locking tab. 4. Repeat step 2 and 3 at 28 cm (11 in.), 43 cm (17 in.), and 57 cm (22.5 in.) from rear of door.
5. Remove outer belt molding.
figure
figure
WEATHERSTRIP - RDB - OUTER📷 2
1. Press the outer belt molding onto the outer door window flange starting at the rear and working forward. 2. Cycle the window to make sure the window doesn't bind on the outer belt molding.
WEATHERSTRIP - REAR DOOR
figure
figure
WEATHERSTRIP - REAR DOOR📷 2
1. Open the rear door. 2. Remove weatherstrip from the body mount flange.
figure
figure
WEATHERSTRIP - REAR DOOR📷 2
NOTE: Position the seal to the bottom of the door opening, with bulb facing outboard, starting the installation at the center of the lower flange. Press the seal onto the sill flange and work around the perimeter of the door opening until fully seated. Work 1/2 the way around and then start at the other end of the seal working back, making sure the splice joint has no gap and smoothing the seal to avoid puckers or wrinkles. If in extreme cold temperatures preheating the weatherstrip to 23.8° C (75° F) may be required to fully seat the weatherstrip.
1. Install the weatherstrip to the body mount flange. 2. Trim the weatherstrip if necessary, and connect the ends together along the flange.
WEATHERSTRIP - RD - MOUNTED
figure
figure
WEATHERSTRIP - RD - MOUNTED📷 1
1. Carefully remove the plastic hook style clips on the weatherstrip from the door and remove the seal from the door.
figure
WEATHERSTRIP - RD - MOUNTED📷 1
1. Position the seal correctly and install the plastic hook style clips on the weatherstrip to the door.
GAP AND FLUSH
figure