‹

Parking Brake Cable

Brakes and Traction Control › Parking Brake System
Unified entry — merged from multiple cross-listed pages in the original manual.

Parts

PartRight
ManufacturerCHY
OEM part #52125206AF
Price$20.85
PartLeft
ManufacturerCHY
OEM part #52125207AF
Price$21.60

Labor

Replace — Rear Cable — One Side1.3 hr
Warranty 0.0 hrSkill B
Procedures
Installation10 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4
Fig. 5
Fig. 5
  1. Install the cables (2) into the axle bracket.
  2. Reconnect the cable to the park brake lever (1).
  3. Install the park brake cable between the stabilizer bar retainer bracket and the mount. Tighten the bolts to 47 Nm (35 ft. lbs.).
  4. Push the cables (1) through the floor (3) and seat the grommets (2).
  5. Reconnect the two cables (1) to the front mount and then to the equalizer (2).
  6. Lay the carpet (2) back down in the rear.
  7. Install the rear seat Rear Seat - Installation.
  8. Remove the lock out device on the lever.
  9. Adjust the park brake shoes Adjustments.
  10. Test the parking brake.
Removal9 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4
Fig. 5
Fig. 5
  1. Lock out the parking brake cables Procedures.
  2. Remove the rear seat Rear Seat - Removal.
  3. Pull the carpet forward far enough in the rear to gain access to the two parking brake cables through the floor.
  4. Disconnect the two cables (1) from the equalizer (2) and then remove the cables front the mount using a proper sized box end wrench over the tangs.
  5. Push the cables (1) through the floor (3) with the grommets (2).
  6. Remove the stabilizer bar bracket retainer.
  7. Remove the park brake cable from the stabilizer bar retainer and mount.
  8. Remove the cable from the axle bracket with a proper sized box end wrench over the tangs.
  9. Remove the brake cable (2) from the brake lever (3).
Factory service manual
From the 2008 KK factory manual — descriptions, specs, torque & procedures for this part.
REAR PARKING BRAKE CABLES📷 4
1. Lock out the parking brake cables. See ADJUSTMENTS.
1 - PARK BRAKE CABLES 2 - CARPET
2. Remove the rear seat. Refer to REMOVAL . 3. Pull the carpet forward far enough in the rear to gain access to the two parking brake cables through the floor.
4. Disconnect the two cables (1) from the equalizer (2) and then remove the cables front the mount using a proper sized box end wrench over the tangs.
5. Push the cables (1) through the floor (3) with the grommets (2).
  6.   Remove the stabilizer bar bracket retainer.
  7.   Remove the park brake cable from the stabilizer bar retainer and mount.
  8.   Remove the cable from the axle bracket with a proper sized box end wrench over the tangs.
  9.   Remove the brake cable (2) from the brake lever (3).
figure
figure
figure
figure
REAR PARKING BRAKE CABLES📷 4
1. Install the cables (2) into the axle bracket. 2. Reconnect the cable to the park brake lever (1). 3. Install the park brake cable between the stabilizer bar retainer bracket and the mount. Tighten the bolts to
47 N.m (35 ft. lbs.).
4. Push the cables (1) through the floor (3) and seat the grommets (2).
5. Reconnect the two cables (1) to the front mount and then to the equalizer (2).
1 - PARK BRAKE CABLES 2 - CARPET
 6.   Lay the carpet (2) back down in the rear.
 7.   Install the rear seat. Refer to INSTALLATION .
 8.   Remove the lock out device on the lever.
 9.   Adjust the park brake shoes. See ADJUSTMENTS.
10.   Test the parking brake.
LEVER
figure
figure
figure
figure