‹

Sunroof / Moonroof Switch

Sensors and Switches › Sensors and Switches - Body and Frame
Unified entry — merged from multiple cross-listed pages in the original manual.

Parts

PartSwitch
ManufacturerCHY
OEM part #68023666AA
Price$12.10

Labor

Replace0.3 hr
Warranty 0.0 hrSkill B
Procedures
Sunroof Switch - Removal4 steps
  1. Disconnect and isolate the negative battery cable.
  2. Remove the overhead console from the headliner, Front Overhead Console - Removal.
  3. Disconnect the sunroof control switch electrical connector. Depress the connector retaining tab and pull the connector straight out.
  4. To remove the switch from the overhead console, push on the back of the switch until it comes free from the overhead console.
Sunroof Switch - Installation4 steps
  1. Install the switch in the overhead console assembly. Be certain the switch is securely snapped in place.
  2. Connect the sunroof control switch electrical connector. Be certain the switch connector is securely snapped in place.
  3. Install the overhead console, Front Overhead Console - Installation.
  4. Connect the negative battery cable.
Sunroof Switch5 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Remove the overhead console. Front Overhead Console - Removal.
  2. Disconnect the power sunroof switch wire harness connector.
  3. With the ignition key in the "RUN" position check for 5 volts on the "OPEN", "CLOSE" and "VENT" circuits of the sunroof switch harness connector. If OK, go to 4. If not OK, inspect the wiring harness and connectors between the motor/module and switch for damage and repair as necessary.
  4. With the ignition key in the "OFF" position check for continuity between the ground circuit of the sunroof switch harness connector and a known good ground. Continuity should be present. If OK, go to 5. If not OK, inspect the wiring harness and connector and repair the ground circuit as necessary.
  5. Using an ohmmeter, test the continuity of the power sunroof switch in each switch position. Refer to the POWER SUNROOF SWITCH CONTINUITY TABLE. If OK, inspect the wiring harness and connectors for damage and repair as necessary. If not OK, replace the overhead console assembly. Front Overhead Console - Removal. POWER SUNROOF SWITCH CONTINUITY TABLE
Full Open Retractable Roof Switch5 steps
Fig. 1
Fig. 1
Fig. 2
Fig. 2
  1. Remove the overhead console. Front Overhead Console - Removal.
  2. Disconnect the full open retractable roof switch wire harness connector.
  3. With the ignition key in the "RUN" position check for 5 volts on the "FRONT OPEN", "REAR OPEN" and "CLOSE" circuits of the switch harness connector. If OK, go to 4. If not OK, inspect the wiring harness and connectors for damage and repair as necessary.
  4. With the ignition key in the "OFF" position check for continuity between the ground circuit of the switch harness connector and a known good ground. Continuity should be present. If OK, go to 5. If not OK, inspect the wiring harness and connector and repair the ground circuit as necessary.
  5. Using an ohmmeter, test the continuity of the full open retractable roof switch in each switch position. Refer to the FULL OPEN RETRACTABLE ROOF SWITCH CONTINUITY TABLE. If OK, inspect the wiring harness and connectors for damage and repair as necessary. If not OK, replace the overhead console assembly. Front Overhead Console - Removal. FULL OPEN RETRACTABLE ROOF SWITCH CONTINUITY TABLE
Switch, Control Switch3 steps
Fig. 1
Fig. 1
  1. Remove the overhead console from the headliner, Front Overhead Console - Removal.
  2. Remove the sunroof control switch from the overhead console, Sunroof Switch - Removal.
  3. Using an ohmmeter, test the switch terminals for proper continuity using the table below. If any of the terminals do not show proper continuity, replace the sunroof control switch.
Sunroof Switch - Description — Power Top Switchreference
Fig. 1
Fig. 1
DESCRIPTION The power sunroof switch (2) is a combination push-button and rocker switch module mounted in the overhead console assembly (1). The sunroof switch is a direct contact unit that is directly wired to the sunroof motor/module assembly. The sunroof switch performs the following functions: -Power sunroof open (back of switch pushed) -Power sunroof express open (back of switch pushed and released) -Power sunroof closed (front of switch pushed) -Power sunroof express closed (front of switch pushed and released) -Power sunroof vent (switch center button pushed) The power sunroof switch is part of the overhead console assembly and cannot be serviced separately. If the switch is damaged or inoperative the overhead console assembly must be replaced. Front Overhead Console - Removal.
Full Open Retractable Roof Switch - Descriptionreference
Fig. 1
Fig. 1
DESCRIPTION The full open retractable roof switch (2) is a combination push-button and rocker switch module mounted in the overhead console assembly (1). The power roof switch is a direct contact unit that is directly wired to the roof Electronic Control Unit (ECU) (sometimes referred to as the Power Top Control Module). The power roof switch is part of the overhead console assembly and cannot be serviced separately. If the switch is damaged or inoperative the overhead console assembly must be replaced. Front Overhead Console - Removal.